Brake pad powder
We are a manufacturer based in China, specializing in high-quality Brake pad powder for industrial clients worldwide. Technical support and custom formulation available.
Category：powder Coating | Brand：MT
Introduction
Brake Pad Powder
Selecting a powder coating that meets the specific requirements of each industry can be challenging. Our industry-focused powder coatings are formulated with materials and processing adjustments to suit different substrates and application needs. Brake Pad Powder is designed for brake pad components, with application characteristics intended to support uniform coverage of metal edges and suitable flexibility during subsequent processing.
Product Features
Uniform Application
Designed to support even powder coverage on different substrates, including metal plate edges.
Suitable Flexibility
Formulated to support edge processing and chamfering with reduced burr formation.
Application-Specific Formulation
Developed for the coating requirements of brake pad components.
Product Specifications
| Parameter | Specification |
|---|---|
| Product Name | Brake Pad Powder |
| Applicable Industry | Automotive brake pads |
| Powder Specific Gravity | 1.2–1.8 g/cm³ |
| Storage Stability | 12 months when stored below 30°C. Retest after the storage period before use. |
| Curing Conditions | 200°C for 12 minutes or 180°C for 15 minutes, based on workpiece surface temperature. |
Physical Properties
| Test Item | Test Standard | Result |
|---|---|---|
| Bending | ASTM D522 | Pass; curvature diameter 5 mm |
| GB/T 1731 | Pass; curvature diameter 2 mm | |
| Dry Adhesion | ASTM D3359 | 5B |
| ISO 2409 | Grade 0 | |
| GB/T 9286 | Grade 0 | |
| Cupping | ISO 1520 | Pass at 5 mm; no coating cracking or detachment |
| GB/T 9753 | Pass at 5 mm; no coating cracking or detachment | |
| Positive Impact Resistance | ASTM D2794 | ≥ 50 kg·cm |
| GB/T 9753 (as listed in source) | 50 kg·cm | |
| Pencil Hardness | ASTM D3363 | ≥ H |
| GB/T 6739 | ≥ H |
Pretreatment and Application
Substrate pretreatment: Metal substrates should be cleaned and degreased before coating. For ferrous metals, zinc or iron phosphating may be used to improve corrosion resistance. The original instructions specify chromate treatment for aluminum; confirm the appropriate conversion treatment for the substrate and applicable environmental requirements.
Application equipment: Manual or automatic powder spraying equipment can be used. Automatic spraying is recommended where consistent coating coverage is required. Unsprayed powder may be recovered using a suitable powder recovery system.
| Application Parameter | Original Specification |
|---|---|
| Atomizing Air Pressure | Approximately 0.5 bar |
| Primary Air Pressure | Approximately 0.5 bar |
| Spraying Voltage | 40–90 kV |
Coating Damage Repair
- Grind the damaged surface and remove dust using clean air.
- Recoat the prepared area and reduce the spraying voltage as needed for repair application.
Safety Information
- Do not eat, drink, or smoke during powder spraying.
- Avoid inhaling airborne powder and wear a suitable respiratory protective device.
- Consult the product-specific Safety Data Sheet (SDS) for handling, storage, exposure controls, and other safety precautions.
Technical Disclaimer
The information provided is based on current product knowledge and is intended as general technical guidance. Actual coating performance depends on substrate condition, pretreatment, application settings, curing conditions, and other factors outside the manufacturer’s control. Users should verify product suitability for the intended application and comply with applicable local laws and regulations. Consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS) before use. Unless otherwise confirmed in writing, the information does not constitute a guarantee of performance under every application condition. Product supply is subject to the manufacturer’s applicable terms and conditions of sale.
Contact our team for technical specifications, sample availability, and application guidance for Brake Pad Powder.
Inquiry
We'll reply within 24 hours
